PPP generic driver version 2.4.2
usb 2-2: USB disconnect, address 2
usb 2-2: new full speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X9010) : Eagle I
usb 2-2: reset full speed USB device using uhci_hcd and address 3
usb 2-2: [ueagle-atm] pre-firmware device, uploading firmware
usb 2-2: [ueagle-atm] loading firmware ueagle-atm/eagleI.fw
usb 2-2: [ueagle-atm] firmware uploaded
usb 2-2: USB disconnect, address 3
usb 2-2: new full speed USB device using uhci_hcd and address 4
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X900F) : Eagle I
usb 2-2: reset full speed USB device using uhci_hcd and address 4
usb 2-2: [ueagle-atm] using iso mode
usb 2-2: [ueagle-atm] (re)booting started
usb 2-2: [ueagle-atm] modem operational
usb 2-2: [ueagle-atm] ATU-R firmware version : 44e2ea17

lsmod | grep ppp :

ppp_async 16640 0
pppoatm 10624 0
ppp_generic 33952 2 ppp_async,pppoatm
slhc 11392 1 ppp_generic
crc_ccitt 6784 2 ppp_async,irda

Diagnostic () driver ueagle-atm 20070726174114
# System Information
Linux version 2.6.18-4-amd64 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 11:36:53 CEST 2007
usb_storage 87616 1
pppoatm 10624 0
ppp_generic 33952 2 ppp_async,pppoatm
scsi_mod 153008 3 sd_mod,usb_storage,sbp2
ueagle_atm 31940 0
firmware_class 15616 2 pcmcia,ueagle_atm
usbatm 23808 1 ueagle_atm
ohci1394 38216 0
ieee1394 361976 3 sbp2,eth1394,ohci1394
ehci_hcd 36104 0
ide_core 147584 5 usb_storage,ide_cd,ide_disk,via82cxxx,generic
uhci_hcd 28696 0
eth0 Lien encap:UNSPEC HWaddr 00-03-25-21-36-00-37-B7-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

eth1 Lien encap:Ethernet HWaddr 00:03:25:13:06:F8
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:185 Adresse de base:0x1800

lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:HÃŽte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:208 errors:0 dropped:0 overruns:0 frame:0
TX packets:208 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:16064 (15.6 KiB) TX bytes:16064 (15.6 KiB)

sit0 Lien encap:IPv6-dans-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

Table de routage IP du noyau
Destination Passerelle Genmask Indic Metric Ref Use Iface
ueagle-atm status display
-------------------------------------------------------------
Vendor ID : 0x1110 Product ID : 0x900f Rev: 0x410b(pots)
USB Bus : 002 USB Device : 004 Dbg : 0
VID-CPE 28

Tx Rate 160 Kps Rx Rate 1216 Kps
Tx Atten 19 dB Rx Atten 25 dB
Tx Margin 27 dB Rx Margin 31 dB
Tx Blocks 2314812 Rx Blocks 2314812
Tx FEC 0 Rx FEC 0
Tx Error 0 Rx Error 0
Delin GOOD Flags 0000000000
Modem is operational

# ping IP ? [ KO ]
# test DNS resolution ? [ KO ]

#
# /etc/ppp/pap-secrets
#
# This is a pap-secrets file to be used with the AUTO_PPP function of
# mgetty. mgetty-0.99 is preconfigured to startup pppd with the login option
# which will cause pppd to consult /etc/passwd (and /etc/shadow in turn)
# after a user has passed this file. Don't be disturbed therefore by the fact
# that this file defines logins with any password for users. /etc/passwd
# (again, /etc/shadow, too) will catch passwd mismatches.
#
# This file should block ALL users that should not be able to do AUTO_PPP.
# AUTO_PPP bypasses the usual login program so it's necessary to list all
# system userids with regular passwords here.
#
# ATTENTION: The definitions here can allow users to login without a
# password if you don't use the login option of pppd! The mgetty Debian
# package already provides this option; make sure you don't change that.

# INBOUND connections

# Every regular user can use PPP and has to use passwords from /etc/passwd
* hostname "" *

# UserIDs that cannot use PPP at all. Check your /etc/passwd and add any
# other accounts that should not be able to use pppd!
guest hostname "*" -
master hostname "*" -
root hostname "*" -
support hostname "*" -
stats hostname "*" -

# OUTBOUND connections

# Here you should add your userid password to connect to your providers via
# PAP. The * means that the password is to be used for ANY host you connect
# to. Thus you do not have to worry about the foreign machine name. Just
# replace password with your password.
# If you have different providers with different passwords then you better
# remove the following line.

# * password

"monlogin@FAI" * "mdp"

user "monlogin@FAI"
plugin pppoatm.so 8.35
llc-encaps
noipdefault
usepeerdns
defaultroute
persist
noauth

pppd call ueagle-atm
Plugin pppoatm.so loaded.